Expert Answers about Ford Snow Plow
- Recommended Snow Plow and Front End Suspension for a 1994 Ford Ranger
- Yes, the Custom Mounting Brackets for Detail K2 Snowplows item # K281110 are confirmed to fit your 1994 Ford Ranger. These will allow you to mount the Detail K2 Storm II Snowplow item # K2STOR8422 to your truck.
It is recommended when using a snow plow to add additional suspension support. I recommend the Timbren Front Suspension Enhancement System item # TFXF1004 which fits the 4WD models of the 1994 Ranger.
view full answer... - How To Replace Battery on Wireless Handheld Remote for SnowBear Single Speed Electric Snowplow Winch
- The 9v Battery # DU88QR in the Replacement Wireless Handheld Remote for SnowBear Single Speed Electric Snowplow Winch # SB263-284 can be replaced by removing the battery door with a Philips head screw driver on the back of the remote as seen in the picture.
view full answer... - Replacement motor for plow
- It sounds like you're actually going to need 1306320 which is for the older style single post design. We do not carry this unfortunately, but a quick google searched pulled up some sites to purchase it from.
SAM 1306320 4-1/2" Motor (Old Style) For Western Snow Plows. Replaces Western OEM part number 25556A. This style motor 4-1/2" replaces the older style 4-1/2 or 4 inch Western motors.
view full answer... - Which Front Mount Receiver Should I use on My 2009 Ford F-150 For The SnowBear Personal Snowplow?
- Both the Curt Front Mount Trailer Hitch Receiver # C31068 and Draw-Tite Front Mount Trailer Hitch Receiver 65061 have been tested by each manufacturer for their respective weight ratings. I would not be concerned with the Draw-Tite having a longer receiver as a limiting factor.
The longer receiver tube will likely make it easier for you to install your SnowBear Personal Snowplow # SB324-140. The hitch shank on the SnowBear has multiple mounting points that will allow you to adjust the...
view full answer... - What Fluid in Cold Climate For Replacement 7 Quart Vertical Pump for Lippert Hydraulic Leveling
- I'm not sure what your snow plow uses, but here is the official word from Lippert on the correct fluid for cold climates (operates at temps often below 32 degrees Fahrenheit) with the Replacement 7 Quart Vertical Pump Assembly for Lippert Components Hydraulic Leveling System # LC251910:
A. Mobil 1 full synthetic ATF
B. Royal Purple full synthetic ATF
C. Valvoline full synthetic ATF
D. Amsoil full synthetic ATF
E. PetroBlend (Mason City, IA) PHO 0022S (synthetic group 3 base blend)
F. Bellman...
view full answer... - Front Hitch And Front Suspension Enhancement For A 2024 Ram 2500
- We can definitely help set you up! There is a front mount hitch available for the 2024 Ram 2500 with the Curt # C73ZV. It will be a direct bolt-on install and some minor trimming of the bumper fascia may be required.
As far as front suspension enhancement, I highly recommend the Timbren # T98GR. These are 6,000 lb rated rubber jounce springs that are basically designed specifically for trucks with plows. They will help to eliminate any sagging while adding stability and absorbing shock....
view full answer... - Will Replacement Cutting Edge for Curtis Snow Plows Replace 4" Tall Cutting Edge
- There won't be any issue with the height difference on the # 3371304801. Since the mounting holes line up you're good to go. This is 3/8" thick just like the one you originally had. A 1/2" thick version # 3371304805 is also available.
view full answer... - Replacement Seal For An Older Meyer ST-90 Snow Plow
- Hi Greg, so the ST-90 plows have been discontinued since 2009 I believe, but I was able to find a manual on the Meyer website. The manual indicates that the cylinder on the ST-90 uses the 07705 seal, for which our seal # 3371305100 will be the correct replacement. The 1-1/2" x 10" cylinder in your picture looks identical to the one in the manual, so it definitely should work.
I am afraid we do not have any videos or manuals that we can send for replacing the seal. From why understand replacing...
view full answer... - Recommended Tire Chains For A 2022 Honda CR-V With 235/60R18 Tires
- Hey Dennis thanks for your question. I can definitely point you in the right direction, although it sounds like you are already on the right track. Both of the options you mentioned, the Konig XG-12 Pro 247 # TH01594247 and the Pewag Servo RS # PWRS80 are going to fit the 235/60R18 tires on your 2022 Honda CR-V. Both will also be very similar as far as installation since they are drape-over style self-tensioning chains.
A drape over chain is certainly what I would recommend for your situation....
view full answer...
Go To Results